9:40 p.m.
Akido
In all situations flooded streets, is the best way ... do not go through or restricted.
Where there is no choice, forced to venture through flooded areas should be motivated to remove the air filter to remove wind directly into the engine compartment (highest position) via the air without charge under the car ( lower position). Beyond the flooding, the engine re-installed air filters as original. However, the water safety warning is less than 25 cm, not through the wheel center.
Special attention when driving in the same direction and opposite direction will occur to create waves, capable of high water and flooding roads wind load, the engine air filter. Stock inlet on the Ford Laser, which are vulnerable to water.Stock inlet on the Ford Laser, which are vulnerable to water.
Should switch off the AC (air conditioning), went No. 1, all stations run at a moderate level, keeping the machine full blast, driving calmly. With an automatic car, switched to semi-automatic and at 1. If you leave, the car will make to the No. 2 station was weak, leading to overflow into the engine through the pipe po. Pedal cars should not taper the floor when the room flooded.
Many drivers have said that paddy ga real hard to pass cars. In fact this solution is very dangerous because power station will cause increased water flow through the grille, flowing into the syringe. In addition, when gas rose dramatically higher rpm machine, if the water in hydro-file will make a stronger phenomenon, leading to a curved boundary hands.
Through the flooded room, you need to go forward a paragraph, brake clearance to remove the disk. Then check back down the engine, chassis.
If the car is suddenly off the flooded area, absolute and must be restarted immediately contact telephone hotline rescue, agents or salespeople for advice guides, find measures optimal for processing.
The reason is that the normal machine operation, the piston forced labor to load the gas mixture at a rate of 1,000 rpm. Because the gas mixture was loaded and occupied the country since the water is not compressible, so pressure has created a jet to deform the curved edge and piston arms, your hands are too curved boundary will be broken. This would breach paragraph breaks into your engine destroyed
When you call for rescue or drivers also noted if the car equipped automatic system, automatic anti-slide, automatically install the bridge, turn automatic stability against the 4WD or full time so only by towing Car Desk (4 wheels not turning).
Where there is no choice, forced to venture through flooded areas should be motivated to remove the air filter to remove wind directly into the engine compartment (highest position) via the air without charge under the car ( lower position). Beyond the flooding, the engine re-installed air filters as original. However, the water safety warning is less than 25 cm, not through the wheel center.
Special attention when driving in the same direction and opposite direction will occur to create waves, capable of high water and flooding roads wind load, the engine air filter. Stock inlet on the Ford Laser, which are vulnerable to water.Stock inlet on the Ford Laser, which are vulnerable to water.
Should switch off the AC (air conditioning), went No. 1, all stations run at a moderate level, keeping the machine full blast, driving calmly. With an automatic car, switched to semi-automatic and at 1. If you leave, the car will make to the No. 2 station was weak, leading to overflow into the engine through the pipe po. Pedal cars should not taper the floor when the room flooded.
Many drivers have said that paddy ga real hard to pass cars. In fact this solution is very dangerous because power station will cause increased water flow through the grille, flowing into the syringe. In addition, when gas rose dramatically higher rpm machine, if the water in hydro-file will make a stronger phenomenon, leading to a curved boundary hands.
Through the flooded room, you need to go forward a paragraph, brake clearance to remove the disk. Then check back down the engine, chassis.
If the car is suddenly off the flooded area, absolute and must be restarted immediately contact telephone hotline rescue, agents or salespeople for advice guides, find measures optimal for processing.
The reason is that the normal machine operation, the piston forced labor to load the gas mixture at a rate of 1,000 rpm. Because the gas mixture was loaded and occupied the country since the water is not compressible, so pressure has created a jet to deform the curved edge and piston arms, your hands are too curved boundary will be broken. This would breach paragraph breaks into your engine destroyed
When you call for rescue or drivers also noted if the car equipped automatic system, automatic anti-slide, automatically install the bridge, turn automatic stability against the 4WD or full time so only by towing Car Desk (4 wheels not turning).
Also, due to lose so many drivers open the door without paying attention to water levels. If the water is higher than the lowest part of the door, never opened, because the water will overflow into external damage to the electronic system, when it should open a window to the car.
4 nhận xét:
Rice milling machinery exporters
MILLTEC Machinery Pvt Ltd is the leading technology providing company for rice milling, Roller flour milling, Maize (corn) milling and pulses processing plants.Rice Milling Machinery, Rice processing equipments, Rice milling Technology, Rice milling equipments, Paddy processing machinery,Rice machinery manufacturer, service provider, Manufactures, exporters,MILLTEC Machinery Pvt Ltd, in bangalore, India.
http://www.milltecmachinery.com/
Rice milling machinery exporters
MILLTEC Machinery Pvt Ltd is the leading technology providing company for rice milling, Roller flour milling, Maize (corn) milling and pulses processing plants.Rice Milling Machinery, Rice processing equipments, Rice milling Technology, Rice milling equipments, Paddy processing machinery,Rice machinery manufacturer, service provider, Manufactures, exporters,MILLTEC Machinery Pvt Ltd, in bangalore, India.
http://www.milltecmachinery.com/
MILLTEC Machinery Pvt Ltd is the leading technology providing company for rice milling, Roller flour milling, Maize (corn) milling and pulses processing plants.Rice Milling Machinery, Rice processing equipments, Rice milling Technology, Rice milling equipments, Paddy processing machinery,Rice machinery manufacturer, service provider, Manufactures, exporters,MILLTEC Machinery Pvt Ltd, in bangalore, India.Rice Milling, Rice Machinery, Rice milling machinery exporters, Rice processing equipments manufacturers, Rice milling Technology service provider, Rice machinery manufacturer, Rice milling equipments manufacturers, Paddy processing machinery manufacturers, MILLTEC Machinery Pvt Ltd, Bnagalore.India.
MILLTEC Machinery Pvt Ltd is the leading technology providing company for rice milling, Roller flour milling, Maize (corn) milling and pulses processing plants.Rice Milling Machinery, Rice processing equipments, Rice milling Technology, Rice milling equipments, Paddy processing machinery,Rice machinery manufacturer, service provider, Manufactures, exporters,MILLTEC Machinery Pvt Ltd, in bangalore, India.Rice Milling, Rice Machinery, Rice milling machinery exporters, Rice processing equipments manufacturers, Rice milling Technology service provider, Rice machinery manufacturer, Rice milling equipments manufacturers, Paddy processing machinery manufacturers, MILLTEC Machinery Pvt Ltd, Bnagalore.India.
Post a Comment